STEM Home SchoolExplore. Experiment. Build. Discover.

DIY Water Filter Challenge for KS3: Build, Test and Measure

Build a multi-layer DIY water filter, test four designs with real data, try a free simulator and print the KS3 work log. Ages 11–14, 45–60 minutes.

Start the activityDownload worksheet (PDF)
Colour key:💡 Big Idea📚 New Words🔬 Try It⚠️ Watch Out🧠 Think
🚀 Today’s mission

Design, build and test a multi-layer water filter, then prove which design works best with real numbers

⏱️ 45–60 minutes🎒 KS3 · Ages 11–14🧪 Gravel, sand, carbon🍾 A 2-litre bottle📊 Real data & maths

Free printable: learning outcomes and work log

Two A4 pages: what you are learning, a filter design box, a results table for four trials, the flow-rate and recovery sums, and a trade-off conclusion. No email needed.

Download the free PDF
PDF · 2 pages · Ages 11–14 · KS3
💡 Big Idea

Clean tap water does not come straight from a river. Engineers clean it by passing it through layers that get finer from top to bottom, so big bits are caught first and tiny bits last. In this challenge you build that filter in a bottle, then measure how fast it runs and how clear the water comes out.

The clever part is the order of the layers. Gravel on top catches leaves and lets water rush through. Fine sand in the middle traps tiny dirt. Activated carbon near the bottom grabs colour and smell. Get the order right and muddy water comes out clear. Get it wrong and the filter clogs or the dirt slips through.

🎯 What you will learn
  • Separate: I can explain how filtration separates insoluble solids from a liquid, and name the filtrate.
  • Adsorption vs filtration: I can explain how activated carbon removes colour and smell by adsorption, and why sand cannot.
  • Design and improve: I can build a prototype, change one layer, and say whether it got better or worse.
  • Measure and calculate: I can measure volume in millilitres and time in seconds, and work out the flow rate in mL/s.
  • Judge safety: I can explain why a filter removes visible dirt but still cannot make water safe to drink.

Curriculum link: KS3 Science (chemistry — pure and impure substances, separation techniques) and Design & Technology. See the full KS3 curriculum →

📚 New Words

These are the exact words engineers use. Tap each card to see what it means in plain English.

How does a multi-layer water filter work?

A multi-layer water filter works by stacking materials from the largest pore size at the top to the smallest at the bottom, so each layer catches smaller and smaller bits as the water sinks through. This is called a depth filter, and it is the same idea a water treatment plant uses on a huge scale.

If you poured muddy water straight onto fine sand, the surface would clog in seconds. Grading the layers stops that from happening:

Layer (top to bottom)What it doesHow it works
Coarse gravelCatches leaves, twigs and big lumps.Wide gaps (big pore size) let water rush through without clogging.
Fine sandTraps fine soil and silt.Tiny gaps (small pore size) trap small particles by mechanical filtration.
Activated carbonRemoves colour, chemicals and smell.A huge hidden surface area grabs molecules by adsorption. One gram can have over 500 m² of surface.
Cotton baseHolds the loose layers in.Stops sand and carbon washing out into your clean water.

Below, test that idea for yourself before you build anything. Drag the sliders to change how thick each layer is, and watch what happens to the clarity, the flow rate and the amount of water you get back.

🧪 Interactive water filter simulator

Change the thickness of each layer and watch the turbidity, flow rate, dye removal and water recovery change, before you build the real thing.

200 mL of muddy water in ↓
Clean(ish) water out

Wide gaps. Catches leaves and big bits. Lets water rush through.

Tiny gaps. Traps fine dirt. Slows the water down a lot.

Grabs colour and smell by adsorption. Nothing else removes the dye.

Cotton base: 2 cm (fixed) — holds the media in.

Turbidity (1 clear – 10 muddy)
1
Flow rate
0.86
mL per second
Dye & odour removal
Excellent
Water recovery
80%
of the 200 mL comes out

What to notice: adding fine sand clears the dirt but slows the water down. Adding activated carbon is the only way to remove the green dye and the smell. And making any layer thicker lowers your water recovery, because more water gets trapped in the gaps. That tug-of-war between clean and fast is the heart of this engineering challenge.

What you need to build a water filter

Gather these for each filter. Most are cheap, and the activated carbon is sold in the aquarium aisle of any pet shop.

🎒 Filter and media
  • 1 clear 2-litre plastic bottle
  • Coarse gravel or aquarium stones (about 250 g, rinsed)
  • Fine play sand or silica sand (about 250 g)
  • Granular activated carbon (about 100 g, rinsed in a strainer first)
  • 4–6 cotton balls, or a square of cheesecloth, with a rubber band
📏 Measuring kit
  • A measuring jug or cylinder marked in millilitres (mL)
  • A stopwatch (a phone works)
  • A ruler, to measure each layer in centimetres
  • A standard “dirty water” sample: 500 mL tap water + 2 tablespoons of soil + 1 teaspoon of crushed dried leaves + 3 drops of food colouring + ½ teaspoon of vinegar (for smell)
⚠️ Watch Out

Never drink the water from your filter, even if it looks perfectly clear.

A homemade filter does not remove dissolved chemicals, heavy metals or microscopic germs (pathogens). An adult should help with cutting the bottle. Wash your hands with soap after handling soil and dirty water.

How to build the water filter, step by step

  1. Make the funnel. Ask an adult to cut the bottle in half about 18 cm from the top. Turn the top half upside down and sit it inside the bottom half. The bottom catches the clean water (the filtrate); the top holds your layers.
  2. Add the cotton base (about 2 cm). Push 4–5 cotton balls into the neck. Not so tight that water cannot drip, not so loose that sand falls through.
  3. Add activated carbon (about 3 cm). Pour rinsed carbon on top of the cotton. Tap the sides so it settles evenly.
  4. Add fine sand (about 5 cm). Spoon it on slowly so you do not stir up the black carbon underneath.
  5. Add coarse gravel (about 5 cm). This catches big bits and stops the pouring water from digging a hole in the sand.
  6. Prime the filter. Pour 200 mL of clean tap water through first and throw it away. This rinses out loose dust and settles the layers.
  7. Test and record. Stir your dirty water, measure exactly 200 mL, and start the stopwatch the moment you pour it on. Stop timing when it slows to about one drip every five seconds. Measure how much came out, and score the clarity from 1 (clear) to 10 (muddy).

Real experimental data: four filter designs compared

One test is never enough in engineering. Here is a real classroom data set. Every design was given the same 200 mL of muddy water (starting turbidity 10/10, a vinegar smell and green dye).

Design (layers, top→bottom)Water out (mL)Time (s)Flow rate (mL/s)Clarity (1 clear – 10 muddy)Smell & dye
1. Gravel & cotton only190257.608 — very cloudyNot removed
2. Gravel, sand, cotton (no carbon)1651401.183 — dirt gone, still greenPoor
3. Reversed (fine sand on top)1403100.452 — but the top cloggedGood, but very slow
4. Standard multi-layer1601850.861 — nearly clearExcellent

Trial 1 is fast but useless: the water rushes through and the dirt goes with it. Trial 2 clears the dirt but leaves the water green, because only carbon removes dye. Trial 3 proves why layer order matters — fine sand on top clogged, dropping the flow to a crawl. Trial 4, graded coarse-to-fine with carbon, is the winner: clear, colourless and still usable.

How to calculate your engineering numbers

Use your own measurements and these two formulas. The simulator above uses the same maths.

🧮 1. Flow rate

Flow rate tells you how quickly your filter makes water.

Flow rate equals filtrate volume divided by time

Worked example, using Trial 4:

Worked example: 160 mL divided by 185 s is about 0.86 mL/s

🧮 2. Water recovery

Notice that only 160 mL of the 200 mL came out of Trial 4. Where did the missing 40 mL go? It was trapped in the gaps between the grains. Water recovery is the percentage you get back.

Water recovery equals volume out divided by volume in, times 100

Worked example, using Trial 4:

Worked example: 160 mL divided by 200 mL times 100 is 80 percent

Now put your own numbers in and let the tool do the arithmetic:

🧮 Work out your filter’s numbers

Type in what you measured. The two numbers engineers care about are worked out for you.

Flow rate

= 0.86 mL/sHow fast your filter makes water.

Water recovery

= 80%The rest is trapped in the layers.
💡 The key engineering trade-off

There is almost always a trade-off between speed (flow rate) and cleanliness (low turbidity). Big gaps let water through fast but let dirt through too. Tiny gaps trap the dirt but slow the water to a trickle.

A good engineer does not just pick the cleanest or the fastest. They pick the design that is clean enough and fast enough for the job — which is exactly what Trial 4 does.

Why can’t you drink the filtered water?

Even crystal-clear filtrate is not safe to drink, for two reasons. First, soluble things like salt dissolve into particles thousands of times smaller than any gap in sand or carbon, so they pass straight through. Removing dissolved salt needs reverse osmosis or distillation, not a bottle filter. Second, pathogens — bacteria and viruses — are far too small for mechanical filtration to trap. Real treatment plants add a disinfection step (chlorine, ozone or UV light) after filtering. Your filter does the same job as the filtration stage of a treatment plant, but only that one stage.

From your bottle to a real water treatment plant

Your filter is a tiny model of how a city cleans millions of litres a day. A treatment plant adds a few extra stages around the same core idea:

  1. Coagulation. Safe chemicals make tiny dirt particles clump into larger bits called floc.
  2. Sedimentation. The heavy floc sinks and is removed.
  3. Filtration. The water passes through beds of gravel, sand and carbon — just like your bottle.
  4. Disinfection. Chlorine, ozone or UV light kills the germs a filter cannot catch.
  5. Storage. Clean water is pumped to homes and schools.

Nature does the same thing for free: rain soaks down through soil, sand and porous rock into underground aquifers, coming out clean enough to feed wells and springs.

🧠 Think like an engineer

Use these in your notebook, a science fair board, or around the table:

  • Predict: if you doubled the fine sand from 5 cm to 10 cm, what would happen to the flow rate and the clarity? Use the word pore size.
  • Troubleshoot: a classmate puts carbon on top and gravel at the bottom. Name two problems that happen as soon as they pour in muddy water.
  • Explain: why did Trial 2 remove the brown dirt but not the green dye?
  • Design on a budget: gravel costs £1/cm, sand £1.50/cm, carbon £3/cm, cotton 50p each. Design a filter that reaches a clarity of 2 or better for under £10.

Enjoyed this build? Try the fair test planner to design your own version of this experiment, take the free STEM test for kids to find your level, or explore more engineering challenges.

What is filtration?

Filtration is a way of separating an insoluble solid from a liquid by passing the mixture through a material with small holes. The solid bits are too big to fit through and get trapped, while the liquid — called the filtrate — passes through. In this experiment, layers of gravel, sand and carbon do the filtering.

❓ Questions parents ask

What age and key stage is this water filter experiment for?

It is written for KS3, ages 11 to 14, and links to the KS3 chemistry topic of separation techniques and to Design & Technology. Confident Year 5–6 children can do the build with help, and KS4 students can extend it with the cost-constraint and reverse-osmosis questions.

How do you make a simple water filter at home?

Cut a plastic bottle in half, turn the top upside down into the bottom, and layer cotton, then activated carbon, then fine sand, then coarse gravel. Pour muddy water in the top; cleaner water collects in the bottom. Full step-by-step instructions and a printable are above.

Why do you put the gravel on top and the sand at the bottom?

So the pore size gets smaller as the water sinks. Big gravel gaps catch leaves and let water flow without clogging; fine sand lower down traps the small dirt. If you put fine sand on top it clogs almost at once, as Trial 3 in our data shows.

What does the activated carbon do?

It removes colour, smell and some chemicals by adsorption — molecules stick to its enormous hidden surface area. Sand and gravel cannot do this, which is why the no-carbon design left the water green.

Can you drink the water from a homemade filter?

No. Even clear filtrate can contain dissolved chemicals and microscopic germs that a filter cannot remove. Making water safe to drink needs an extra step such as boiling, chlorine or UV light.

Is this a good science fair project?

Yes. Pick one thing to change — the thickness of a layer, or the order — and keep everything else the same. Test each design three times, record the flow rate and clarity in a table, and show which design was best and why. The printable work log gives you the table to fill in.

Did you finish?

Press the button to collect your Junior Engineer badge.